顯微鏡,工業顯微鏡,視頻顯微鏡

　　<spanstyle="font-family:宋體;TimesNewRoman;TimesNewRoman;">一、產品介紹XQ-3000真空冷鑲嵌機，采用高強度真空室和內置真空泵，排除樣品和冷鑲嵌料料中的空氣，液態鑲嵌料填充試樣中的空隙，以及消除試樣和鑲嵌料之間的間隙，從而實現試樣和鑲嵌料之間的緊密結合。樣品在研磨和拋光過程中也得到良好保護和支撐。二、產品特點1.快速達到高真空（-60KPa）2.真空度數顯，并自動控制。達到設定真空度值后，自動真空泵自動停止，真空下降一定值后，真空泵自動啟動；3.大容積、透明真空室；4.內置真空泵，低噪音，無油、無污染、無需維護5.被鑲嵌樣品和鑲嵌料可被預先抽真空；6.利用真空容器內的旋轉杯架，多個試樣可在真空中一次性澆入到模具中，進行真空鑲嵌；7.專用放氣閥，可實施多次循環抽氣、放氣鑲嵌工藝。8.自帶定時器，鑲嵌完成到后，自動泄壓。三、技術規格名稱<tdwidth="363"valign="top"style="width:272.45pt;border:solidwindowtext1.0pt;border-left:none;padding:0cm5.4pt0cm5.4pt">規格<tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">鑲嵌樣品數量<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">>10個(直徑30mm的鑲嵌模時)<tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">真空室尺寸<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">300Lx300Wx300Hmm<spanstyle="font-family:宋體;"><tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">最大真空度<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">-0.06MPa(-60KPa)<tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">抽氣時間<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">小于1分鐘<tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">模具<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">適用各種形狀的模具：直徑20,40,50mm，或長方形模，或一次性模具<tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">外形尺寸<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">真空室：300Lx300Wx300Hmm主機<spanstyle="font-family:宋體;">箱（內含真空泵）<spanstyle="font-family:宋體">：<spanstyle="font-family:宋體;">L320×W300×H230mm<tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">電源<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">220V，50/60Hz，200W<tdwidth="137"valign="top"style="width:102.4pt;border:solidwindowtext1.0pt;border-top:none;padding:0cm5.4pt0cm5.4pt">重量<tdwidth="363"valign="top"style="width:272.45pt;border-top:none;border-left:none;border-bottom:solidwindowtext1.0pt;border-right:solidwindowtext1.0pt;padding:0cm5.4pt0cm5.4pt">真空容器：1.15kg主機<spanstyle="font-family:宋體;">箱：10Kg